Search Results

This specification covers the requirements for flexible shielded electrical conduit for aircraft installations.

This SAE Aerospace Information Report (AIR) is limited to the subject of compatibility of wiring as part of aircraft Electrical Wiring and Interconnect Systems (EWIS) installed in and around aircraft fuel tanks.

The purpose of this report is to provide recommendations for marking wire and cable insulations to meet legibility requirements. This information is generic and applies to any type of wire marking system, such as an ultraviolet (UV) laser marking system or an inkjet or other ink based wire marking system. This report is limited to the legibility of human-readable characters and does not address bar code or other machine-readable symbols. In this report, the term wire refers to jacketed cables and fiber optic cables in addition to individual wires. This report defines the factors that affect the legibility of markings on wiring. Two generic types of variables affect legibility: stimulus variables and environmental variables. Stimulus variables are those factors involving the mark itself.

The purpose of this report is to provide recommendations for producing legible marks on wire and cable insulations. This information is generic and applies to any type of wire marking system, such as an ultraviolet (UV) laser marking system or an inkjet or other ink based wire marking system. This report is limited to the legibility of human-readable characters and does not address bar code or other machine-readable symbols. In this report, the term wire refers to jacketed cables and fiber optic cables in addition to individual wires. This report defines the factors that affect the legibility of markings on wiring. Two generic types of variables affect legibility: stimulus variables and environmental variables. Stimulus variables are those factors involving the mark itself. This ARP establishes a set of guidelines for key stimulus variables that contribute to legibility and which should be taken into consideration in the course of specifying and using wire marking equipment.

The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide recommendations for marking wire and cable insulations to meet legibility requirements. This information is generic and applies to any type of wire marking system, such as an ultraviolet (UV) laser marking system or an inkjet or other ink based wire marking system. This ARP is limited to the legibility of human-readable characters and does not address bar code or other machine-readable symbols. In this ARP, the term wire refers to jacketed cables and fiber optic cables in addition to individual wires. This ARP defines the factors that affect the legibility of markings on wiring. Two generic types of variables affect legibility: stimulus variables and environmental variables. Stimulus variables are those factors involving the mark itself.

This standard is applicable to manual soldering and machine soldering processes utilizing controlled soldering devices, for electrical connections for wiring and cabling used in aerospace vehicles. Description of a component or device herein is not to be construed as authorizing the use of the component or device.

This standard is applicable to the marking of aerospace vehicle electrical wires and cables using ultraviolet (UV) lasers. This standard specifies the process requirements for the implementation of UV laser marking of aerospace electrical wire and cable and fiber optic cable to achieve an acceptable quality mark using equipment designed for UV laser marking of identification codes on aerospace wire and cable. Wiring specified as UV laser markable subject to AS4373 Test Methods for Insulated Electric Wire and which has been marked in accordance with this standard will conform to the requirements of AS50881.

This standard is applicable to the marking of aerospace vehicle electrical wires and cables using ultraviolet (UV) lasers. This standard specifies the process requirements for the implementation of UV laser marking of aerospace electrical wire and cable and fiber optic cable to achieve an acceptable quality mark using equipment designed for UV laser marking of identification codes on aerospace wire and cable. Wiring specified as UV laser markable subject to AS4373 and which has been marked in accordance with this standard will conform to the requirements of AS50881.

This AIR is limited to the requirements of AS50881 and examines these requirements, providing rationale behind them. AS50881 is only applicable to the aircraft EWIS. Pods and other devices that can be attached to an aircraft are considered as part of the aircraft equipment design. Its scope does not include wiring inside of airborne electronic equipment but does apply to wiring externally attached to such equipment. The AS50881 scope does not include attached devices but does include the interface between the pod/equipment and aircraft wiring. Section 3.3.5 addresses components such as antennas and other similar equipment that were once supplied as Government Furnished Aeronautical/Aerospace Equipment (GFAE).

This document covers the general requirements for Transverse Electromagnetic Mode (TEM) Transmission Lines (see 6.4.14) intended for use in airborne systems.

This document covers the general recommendations for Transverse Electromagnetic Mode (TEM) Transmission Lines intended for use in airborne systems (see 6.2.14). For U.S military applications, TEM Transmission Lines shall meet the requirements in accordance with MIL-T-81490. The follow index lists the recommended requirements and methods covered by the Aerospace Recommended Practice (ARP):

This document covers the general recommendations for Transverse Electromagnetic Mode (TEM) Transmission Lines intended for use in airborne systems (see 6.2.14). For U.S military applications, TEM Transmission Lines shall meet the requirements in accordance with MIL-T-81490. The follow index lists the recommended requirements and methods covered by the Aerospace Recommended Practice (ARP):

This ARP provides recommended use and installation procedures for bonded cable harness supports.

This specification establishes performance requirements for markings that have been applied to electrical insulating materials (see 6.1).

This specification establishes performance requirements for markings that have been applied to electrical insulating materials (see 6.1).

This specification establishes the performance requirements for the identification of wire and cable by indirect markings that have been applied to electrical insulating materials including heat shrink sleeving, wrap around labels and “tie-on” tags as well as any other types of materials used for indirect marking. This specification covers the processes used to mark these materials, including impact ink marking, thermal transfer, hot stamp, and lasers, etc. This specification does not cover the direct marking on insulated electrical wires and cables.

The purpose of this report is to provide information on the results of ultra violet (UV) laser marking and mark contrast measurement of a wide range of aerospace wire and cable constructions, the specifications for most of which do not state specific requirements for laser markability. The contents of this document are for information and guidance only. It is not intended that it be used as the basis for marking process specifications or standards, which are covered by AS5649 Wire and Cable Marking Process, UV Laser.